Maytag Washers Error Codes

Excessive suds

Consider using a different HE detergent. This can be caused by non-HE detergent, or natural, organic, or homemade HE det...

Excessive suds

Consider using a different HE detergent. This can be caused by non-HE detergent, or natural, organic, or homemade HE det...

Remove load

Displayed when clothing or other items are detected in the washer during the Clean Washer with affresh® cycle.

Load detected during Clean Washer cycle

Remove load and restart the Clean Washer cycle.

Oversuds

Check pressure hose connection from tub to ACU. If problem persists, check for proper detergent usage.

Off Balance Load

Balance single item, such as a rug or jeans, with a few extra items.

Appliance Control Unit Fault

Try recycling power to washer. See TEST #1: ACU Power Check, pg. 3-6.

Appliance Control Unit Fault

Try recycling power to washer. See TEST #1: ACU Power Check, pg. 3-6. See TEST #3: Motor Circuit, pg. 3-10.

Water Level Sensor Fault

See TEST #7: Water Level Sensor, pg. 3-14.

Wash NTC Fault

See TEST #10: Wash Temperature Sensor, pg. 3-17.

Dry NTC Fault

See TEST #16: Dry Thermistor Sensor, pg. 3-25.

Accelerometer Fault

Replace the Appliance Control Unit (ACU).

Wash heater relay error or no feedback signal

See TEST #9: Wash Heating Element, pg. 3-16.

Heater Not Turning On

See TEST #9: Wash Heating Element, pg. 3-16.

Vent Fan Motor Fault or Dry Blower Motor Fault

See TEST #13: Vent Fan Motor, pg. 3-22. See TEST #17: Dry Blower Motor, pg. 3-26.

Door Switch Fault

See TEST #4: Door Lock System, pg. 3-11.

Door Lock Will Not Lock or Door Lock Failure

See TEST #4: Door Lock System, pg. 3-11.

Door Unlock Failure

See TEST #4: Door Lock System, pg. 3-11.

Door Not Open Between Cycles

See TEST #4: Door Lock System, pg. 3-11.

Communication Error: ACU Cannot Hear HMI

Try recycling power to washer. Verify continuity in cable between ACU (J19) and HMI (see wiring diagram on pages 3-3 to...

Communication Error: HMI Cannot Hear ACU

Try recycling power to washer. Verify continuity in cable between ACU (J19) and HMI (see wiring diagram on pages 3-3 to...

No Communication between ACU and MCU

Try recycling power to washer. Check AC and DC supplies (See TEST #1, pg 3-6). See TEST #3: Motor Circuit (pg 3-10).

Motor Control/Internal Fault

Try recycling power to washer. Check harness continuity and connections between ACU and motor.

Motor Control/Over Temp Detected

Try recycling power to washer. Check harness continuity and connections between ACU and motor.

Motor Locked Rotor

See TEST #3: Motor Circuit, pg. 3-10.

Motor Control/Lost Phase Fault

Try recycling power to washer. Check harness continuity and connections between ACU and motor.

Motor Control/Motor Overload Fault

Try recycling power to washer. Check harness continuity and connections between ACU and motor.

Long Fill

See TEST #6: Water Inlet Valves, pg. 3-13.

Overflow

Verify functionality of water inlet valve, water level sensor, and drain/recirculation pump.

Long Drain

Check functionality of drain/recirculation pump. See TEST #8 (pg 3-15).

WiFi Error

See Section 5 - Connectivity.

Dryer heater is not turning on

Check for a power supply problem in your house. See "Troubleshooting" section.