LG Washers Error Codes
50 error codes extracted from LG washers service manuals. Each code includes its meaning and a summary fix step.
Error Codes50 codes
INLET ERROR
Make sure that the water faucets are fully open.
UNBALANCE ERROR
Add additional items to allow the washer to balance the load.
DOOR OPEN ERROR
Close and secure the door. If the message keeps appearing, unplug the power cord and call for service.
WATER OUTLET ERROR
Make sure that the drain hose is free of clogs or kinks and is not pinched behind or under the washer.
TEMPERATURE SENSOR ERROR
Unplug the washer and wait 60 minutes. Reconnect power and try again.
OVERFLOW ERROR
Close the water faucets, unplug the washer, and call for service.
PRESSURE SENSOR ERROR
Close the water faucets, unplug the washer, and call for service.
MOTOR LOCKED ERROR
Allow the washer to stand for 30 minutes and then restart the cycle.
OVERSUDSING DETECTION
Do not add more than the manufacturer's recommended amount of detergent.
POWER FAILURE
Press the Start/Pause button to restart the cycle.
FROZEN ERROR
See Care in Cold Climates.
CONTROL LOCK FUNCTION
Turn off the Control Lock function in the control panel. See Control Lock under Options and Extra Functions.
TUB CLEAN ALARM
This is not an error code. It indicates that the Tub Clean cycle is running or needs to be run to clean the washer drum.
VIBRATION SENSOR ERROR
Call for service.
Temperature sensor failure.
Turn off the appliance and call for service.
Electric dryer power cord is not connected correctly, or house power supply is incorrect.
Reset circuit breaker or replace fuse. Do not increase the fuse capacity.
Gas supply or service turned off. (Gas model only.)
Confirm that house gas shutoff and the dryer gas shutoff are both fully open.
Exhaust system is too long or has too many turns/restrictions.
Do not use the appliance until the exhaust system has been cleaned and/or repaired.
More Time button was pressed.
This display indicates that the steam option has been set for a "big" item such as a comforter.
Motor harness is disconnected.
Check the motor harness.
Drum motor failure.
Turn off the appliance and call for service.
Temperature sensor failure.
Turn off the appliance and call for service.
Humidity sensor failure.
Turn off the appliance and call for service.
Installation test activation successful.
N/A
End of test cycle.
N/A
Temperature Sensor has malfunctioned.
Unplug the power plug and call for service.
The temperature inside the drum has risen suddenly.
Unplug the power plug and call for service.
The motor has stopped suddenly.
Check if the amount of clothing exceeds the maximum load capacity. Unplug the power plug and call for service.
The compressor has stopped suddenly.
Unplug the power plug and call for service.
The drain hose is not connected properly. OR The drain pump motor has malfunctioned. OR The temperature at the installation location is below zero.
Connect the drain hose properly. Check if the drain hose is free of clogs or kinks and is not pinched behind or under th...
The fan motor has stopped suddenly.
Unplug the power plug and call for service.
The internal fan has malfunctioned.
Unplug the power plug and call for service.
The appliance is being operated without the condenser cover.
Open the access panel and assemble the condenser cover.
Power cord is connected incorrectly.
Check the connection of the power cord to the terminal block.
The washer was paused during a cycle for more than 4 minutes, the cycle was canceled, and any water remaining in the tub was drained. (This is not an error code, but an indication of drain function operating).
Lid is not locked properly.
Make sure that the lid is closed properly and press the Start/Pause button.
The washer has detected an out of balance load. (This is for information only; no action is required as the washer attempts to rebalance the load).
The washer will automatically add water and try to redistribute the load.
Water pressure is low or an inlet filter is clogged with dirt.
Clean the inlet filter.
The drain pump filter is clogged with dirt.
Clean the drain pump filter.
Washer beeps and nothing happens when a button is pressed.
Turn off Control Lock: press the Options button, turn the knob to select Control Lock, and press the (OK) button.
Water Outlet Error
Make sure that the drain hose is free of clogs or kinks and is not pinched behind or under the washer.
Vibration Sensor Error
Call for service.
Temperature sensor failure.
Turn off the appliance and call for service.
Temperature sensor failure.
Turn off the appliance and call for service.
Electric dryer power cord is not connected correctly, or house power supply is incorrect.
Reset circuit breaker or replace fuse. Do not increase the fuse capacity.
Electric dryer power cord is not connected correctly, or house power supply is incorrect.
Reset circuit breaker or replace fuse. Do not increase the fuse capacity.
Exhaust system is too long or has too many turns/restrictions.
Do not use the appliance until the exhaust system has been cleaned and/or repaired.
Exhaust system is too long or has too many turns/restrictions.
Do not use the appliance until the exhaust system has been cleaned and/or repaired.
Exhaust system is too long or has too many turns/restrictions.
Do not use the appliance until the exhaust system has been cleaned and/or repaired.
Drum motor failure.
Turn off the appliance and call for service.
Need model-specific LG error codes?
Access per-model error codes, part numbers, and detailed fix steps via the Covala API.